# Complete Combustion > Industrial Combustion Engineering & Design Services - Canada ## Posts - [Choosing a Fabricator After Engineering Design (A Design Client's Guide)](https://completecombustion.ca/choosing-a-fabricator-after-engineering-design/): One advantage of working with a design engineering firm is that the fabricator selection stays entirely in your hands. But that freedom only pays off if you know what to evaluate once the engineering package is in hand. Here’s what actually matters when choosing who builds it. Start With Scope-Matched Experience Not every metal fabricator […] - [Burner Management System Design (BMS): Fundamentals](https://completecombustion.ca/burner-management-system-design-fundamentals/): A Burner Management System (BMS) is the safety layer standing between a combustion process and a catastrophic failure. It governs startup sequencing, flame supervision, and shutdown logic — and unlike general process control, it’s subject to strict code requirements that leave little room for interpretation. Core Functions a BMS Must Perform Pre-purge airflow verification before […] - [Fuel Storage System Design: Codes, Sizing & Safety](https://completecombustion.ca/fuel-storage-system-design-codes-sizing-safety/): Fuel storage sizing and layout decisions get made early in a project — often before the combustion system design is finalized — and mistakes here are expensive to fix later. Whether it’s a natural gas regulator station, a propane tank farm, or an oil storage system feeding an industrial furnace, the design has to satisfy […] - [P&ID Combustion Systems Design for Industrial Plants: A Practical Guide](https://completecombustion.ca/pid-development-industrial-combustion-systems/): A Piping & Instrumentation Diagram (P&ID) is the backbone of any industrial combustion system package. It’s the document fabricators build from, TSSA reviewers check against, and operators reference for years after commissioning. Getting it wrong — or leaving it vague — creates rework, field changes, and compliance headaches down the line. What a Combustion P&ID […] - [Why Design Engineering Benefits Industrial Clients (No Contractor Conflicts)](https://completecombustion.ca/design-engineering-benefits-industrial-clients/): Industrial clients evaluating an engineering partner sometimes hesitate at the phrase “design.” It can sound like a gap in service rather than what it actually is: a structural safeguard against conflicts of interest. When an engineering firm also fabricates, installs, or services equipment, every design decision carries a quiet incentive — more scope, more parts, […] - [Heat Treatment Furnace Design: Multi-Zone Temperature Control & Atmosphere Management](https://completecombustion.ca/heat-treatment-furnace-design/): Multi-zone heat treatment furnaces demand precision engineering. Temperature uniformity across the chamber, atmosphere control for solution heat treat, homogenizing, annealing and stress relief, and consistent thermal cycling are non-negotiable for metallurgical outcomes. Poor furnace design can mean scrap runs, inconsistent material properties, and costly downtime. If you’re considering a new heat treatment system or upgrading […] - [industrial combustion engineering Ontario Brampton | Industrial Combustion Engineering in Ontario — P.Eng Stamped Design from Brampton](https://completecombustion.ca/industrial-combustion-engineering-ontario-brampton/): Industrial Combustion Engineering Services Across Ontario – P.Eng Stamped Design A Combustion Engineering Design Practice Based in Brampton, Ontario Complete Combustion is a licensed industrial combustion engineering practice based in Brampton, Ontario, operating under a Professional Engineers Ontario (PEO) Certificate of Authorization. We provide vendor-neutral combustion engineering design services: P.Eng-stamped P&IDs, fuel train design, BMS […] - [industrial burner retrofit engineering Ontario | Industrial Burner Retrofit Engineering — When to Retrofit and What the Package Includes](https://completecombustion.ca/industrial-burner-retrofit-engineering-guide-ontario/): Industrial Burner Retrofit Engineering Signs an Industrial Burner System Needs Engineering Retrofit Legacy industrial burners degrade, become obsolete, and fall out of regulatory compliance. A structured burner retrofit engineering package is required when annual value seat tests are failing, no stamped engineering drawings exist, relay-based BMS panels are no longer maintainable, TSSA Field Approval has […] - [NFPA 86 pre-purge calculation industrial furnace | NFPA 86 Pre-Purge Calculations for Industrial Furnaces and Ovens — Engineering Guide](https://completecombustion.ca/nfpa-86-pre-purge-calculations-industrial-furnaces/): NFPA 86 Pre-Purge Calculations for Industrial Furnaces and Ovens NFPA 86 mandates a timed pre-purge cycle before every burner ignition sequence in Class A and Class B industrial ovens and furnaces. This pre-purge requirement is one of the most critical combustion safety provisions in industrial process heating, preventing ignition of combustible mixtures that may have […] - [CSA B149.3 fuel train design Canada | CSA B149.3 Fuel Train Design Requirements for Industrial Combustion Systems in Canada](https://completecombustion.ca/csa-b149-3-fuel-train-design-requirements-canada/): CSA B149.3 Fuel Train Design Requirements for Industrial Combustion Systems in Canada CSA B149.3 is the governing Canadian standard that dictates the mandatory safety controls, valve configurations, and engineering documentation required for industrial gas-fired combustion systems requiring field approval. For mechanical contractors, plant engineers, and burner service technicians operating in Ontario and across Canada, understanding […] - [TSSA field approval combustion package Ontario | What a TSSA Field Approval Combustion Package Must Include — Ontario P.Eng Guide](https://completecombustion.ca/tssa-field-approval-combustion-package-ontario/): What a TSSA Field Approval Combustion Package Must Include in Ontario In Ontario, any industrial gas-fired appliance that exceeds standard certified appliance ratings — including custom burner systems, industrial furnaces, rotary dryers, mine air heaters, and thermal oxidizers — requires a formal Field Approval from the TSSA before installation. Complete Combustion prepares complete TSSA Field […] ## Pages - [Combustion Engineering Blog Ontario | Complete Combustion](https://completecombustion.ca/blog/) - [Combustion Engineering Design | Complete Combustion](https://completecombustion.ca/) - [Combustion Engineering Quote Ontario | Contact & Quote](https://completecombustion.ca/contact/): Request an Engineering Scope Review or Project Quote Connect directly with our licensed engineering team to discuss your upcoming industrial combustion design, fuel train piping layout, plant electrical modernization, burner automation, or regulatory compliance submittal. Whether you are a mechanical contractor requiring P.Eng-stamped drawing packages, an OEM needing custom thermal calculations, or an industrial plant […] - [Combustion Engineering Codes Resources Ontario | Complete Combustion](https://completecombustion.ca/resources/): Combustion Engineering Resources & Technical Guides Technical articles, code compliance guides, and engineering insights from Complete Combustion – Ontario’s P.Eng-stamped industrial combustion engineering practice. This page is a working reference for the professional credentials behind our designs and the codes and standards that shape every combustion engineering package we issue. Professional Engineering & Certificate of […] - [Combustion Engineering Case Studies | Complete Combustion](https://completecombustion.ca/case-studies/) - [Industrial Combustion Applications | Complete Combustion](https://completecombustion.ca/applications/) - [Combustion Services | Complete Combustion](https://completecombustion.ca/services/) - [Combustion Engineering | TSSA Compliant P.Eng | Complete Combustion](https://completecombustion.ca/about-us/): Independent Industrial Combustion Engineering Complete Combustion (15897777 Canada Inc.) is a P.Eng-led combustion engineering firm serving industrial facilities across Ontario and Canada. We specialize in combustion system design engineering with zero contractor conflicts, delivering code-compliant, construction-ready packages for furnace design, PLC automation, fuel train piping, and TSSA/CSA compliance. Combustion System Design Engineering You Can Trust […] ## Optional - [Agent (MCP protocol)](websites-agents.hostinger.com/completecombustion.ca/mcp) [comment]: # (Generated by Hostinger Tools Plugin)